Broadcasters' Mobile Phone Interface With Twin Four Wire Circuit
The Glensound GS-MPIFW contain a quad band mobile phone, that will allow the unit to be used in most places of the world, where standard GSM networks are available. If your own mobile phone works, the GS-MPIs will work too. The SIM card fits into a front panel slot and is recessed to avoid accidental removal during operation.
Broadcast Headphone Connection
There is a 6.35mm headphone socket for connecting a pair of headphones or a headset. The units are optimised for an impedance from 200 – 2000 ohms. As the MPIs will often be used in noisy environments, a high output level is available using a variety of broadcast headphones and headsets.
Independent Send & Return Audio Connections
GSM telephone balancing is offered with separate XLR audio connections for the send and return signal. The GS-MPIs offer 100% separation between the send and return paths. The send connection is on a balanced XLR (switchable with a mic imput on the GS-MPI004). The return is on a balanced XLR and contains the return audio (caller) only. There is also independent level control for the send and return audio.
RF Shielding Of Audio Circuits
A carefully designed RF shield insulates the audio circuits from all radio frequency interference. The GS-MPIs own RF does not interfere with its own audio circuits ensuring that typical GSM RF interference is never heard.
There is a configurable auto-answer, from off to 9 rings.
There are 10 memories for instant memory dialling of popular numbers.
Simple LED Status Indication
A red and green LED indicate network and call status.
SMA Aerial Connection
A standard SMA aerial connection is provided for the attached right angle antenna (GS-MPI004) or a separate extension aerial (all rack units)
Two x Four Wire/IFB Circuits
Each circuit can be used independently in four wire mode
Versatile Four Wire Output Options (Programme, GSM, IFB)
1. An external programme input can be switched onto either four wire output
2. The incoming audio from the GSM call can be switched onto either four wire output.
3. One circuitâ€™s four wire input can be switched to its output.
Interrupted Feed Back
When the talk button is pressed the talk audio can either replace the selected output or mix over it (IFB).
LEDs & Loop Outputs
Green LEDs give visual indication of return audio, and a d-type connector on rear with loops is active when talkback 1 or 2 are selected.
Two Position Speak Key
The speak keys are in push to talk mode when pushed down, or latch when pushed up. There is a front panel mic or connection for external mic.
Front Panel Monitoring
There is a front panel speaker, with a 6.35mm headphone socket that mutes the speaker when headphones are connected. Adjustable colume control. Programme, phone, and four wire inputs are all mixed here for monitoring.
Front Panel Mic Input
There is a panel mounted microphone and an XLR socket to connect an external mic if required.
- A quad band GSM phone
- Two four wire / IFB circuits
- An extra comms channel
- Low cost backup
AUDIO SPECIFICATIONS - ALL UNITS
|LINE IN / OUT CONNECTORS:||Neutrik XLRs|
|LINE INPUT LEVEL:||0dB|
|INPUT GAIN CONTROL:||+/- 10dB|
|OUTPUT GAIN CONTROL:||+/- 10dB|
|MAX OUTPUT LEVEL (Line out with XLR):||+13dBu|
|HEADPHONE SOCKETS:||6.35mm jack socket|
|HEADPHONE IMPEDANCE:||200-2000 ohms|
|AUDIO FREQUENCY RESPONSE:||Telephone networks provide 300Hz to 3.4 kHz audio bandwidth|
|QUAD BAND GSM FREQUENCIES:||850 MHz, 1800 MHz, 1900 MHz|
|NETWORK:||Will operate on any mobile phone network, with any SIM card|
|RF OUTPUT POWER:||2 watts|
|AERIAL CONNECTOR TYPE:||SMA|
|BATTERIES:||4 x AA cells. When ‘low battery’ LED flashes there is approx. 30 mins remaining|
|EXTERNAL DC INPUT:||+9 to +12 volts. 2.5mm barrel connector, centre +ve|
GS-MPI005, GS-MPI006, GS-MPIFW
|INTERNAL SWITCH MODE POWER SUPPLY:||100-240v 50-60 Hz|
SPECIFIC SPECIFICATIONS - GS-MPIFW (RACKMOUNT GSM WITH 4W)
|DEPTH (Excluding Connectors):||208mm|
|FOUR WIRE CIRCUITS:||2|
TRU Price Guarantee
(Subject to conditions)